Mini Cooper Forum banner

JCW Pro coilover unboxing

70097 Views 64 Replies 30 Participants Last post by  ImaginativeTruth
I decided that for now I'm going to opt for an "OEM+" motif for my JCW. Part of that decision was centered around the fact that the new JCW Pro coilover offering is in fact built by KW, yet still comes with a MINIUSA warranty that spans the new car warranty. Motor City MINI gave me a lovely package price with the coilovers when buying the JCW, so it was an easy decision. Keep in mind the JCW is my daily driver, and I have my turbo Miata built up as the hardcore Hoosier-shod track car, so a dollop of comfort with sporting intentions are the theme here.

The bigger-than normal box fits comfortably in the F56's larger boot. :biggrin5:
JCW Pro coilovers unboxing by Ryephile, on Flickr

The part number is 33502341197 for "retrofit kit sports suspension" (for cars without DDC)
JCW Pro coilovers unboxing by Ryephile, on Flickr

A very nice microfiber bag holds the spring perch adjuster wrench
JCW Pro coilovers unboxing by Ryephile, on Flickr

A little more unpacking shows the foam-wrapped rear springs, thread-locker compound, "Attention: John Cooper Works sport suspension installed" sticker (LOL), and front struts, the expanding foam keeping everything night and snug.
JCW Pro coilovers unboxing by Ryephile, on Flickr

Here's an up-close of the stainless steel front strut, the stickers indicate "Left" and "Right" sides, and the "made by KW" clearly marked.
JCW Pro coilovers unboxing by Ryephile, on Flickr

Here are the dampers and springs all together on the bench. The rear bumpstops have new dust boots snapped into them. I presume the fronts will re-use the original dust boot bellows
JCW Pro coilovers unboxing by Ryephile, on Flickr

The rear springs, rear height adjusters with very nice rubber noise isolators, thread locker, wrench, and sticker. Where should the sticker go? :confused5:
JCW Pro coilovers unboxing by Ryephile, on Flickr

Close up of the rear height adjuster. It's nicely anodized aluminum, likely right off the shelf at KW but anodized black instead of purple. The rubber isolator is actually a very OEM looking 2-piece design that plugs into the coil spring end.
JCW Pro coilovers unboxing by Ryephile, on Flickr

In all it's a very nice looking kit. It's clear it's had an OEM touch over the normal KW offerings, which is a big plus. I'll post more information on the stroke and bumpstops when I remove the stock bits to have a solid comparison.
See less See more
  • Like
Reactions: 5
1 - 2 of 65 Posts
You need a cargo net! Looks awesome...that's hard core!
  • Like
Reactions: 1
The front suspension uses MacPherson struts, so the camber curve is essentially linear. A bit more front negative camber would make the car more neutral in corners, and there is an OEM front knuckle that's cast for -0.5° over original. It's spendy but proper. I might go that route if good quality (& quiet) camber plates aren't made available soon.

I'll say that the factory alignment is very very good for most street applications. MINI did a great job with the kinematics on this new platform.

My Cooper Works is only a few weeks away. Identical to yours.
Black with red roof and black wheels.

I have picked up some original Works accesories as well.....

Red stripe kit
Real diffusor
Exhoust system
Coilover kit
Black light rings front and rear.

Have you done any testing of the suspensjon setting?
Welcome Flash! Ryephile sold his JCW last year, but many of us learned a lot from him! I'm sure others might jump in to help answer your question though!

Your spec sounds great!

1 - 2 of 65 Posts
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.