[camchalmers]

You need to change the whole headunit.

wait what? I thought it was possible to just swap the screen over, what head unit would I need?

 

[camchalmers]

For your car, you can use your existing headunit with an 8.8” screen. You’ll need the screen and all of the surrounding trim.

Yes, the headunit will need to be coded.

So I can use the existing headunit and just upgrade the screen and surround?

 

[camchalmers]

Yes - you need the screen and the surrounding plastics. The trim for the 8.8” screen is all different than the trim for the 6.5” screen. The hazard and radio buttons can swap over, though.

Thanks, have ordered off eBay a complete unit with buttons and ring for £299. Do you which bits need coding?

 

[camchalmers]

Hi - this thread has the details:

8.8” screen retrofit for ENTRYNAV

Hi guys, Today, my 8.8” screen from eBay arrived! First, I ran into some trouble with only half of the screen showing. Apparently others have had this problem when using BimmerCode. After using E-Sys to do the (exact same) coding, it works. It even plays nicely with my Andream CarPlay MMI...

www.minif56.com

Thanks, will take a look!

 

[camchalmers]

Before vs after, all coded in and also took the chance to code cornering fog lights while I was at it!

Before:

After:

 

[camchalmers]

That looks really good, plus the £300 for the screen and surround is a bit of a bargain - I've been looking for a while but only seen examples with damaged screen for that kind of cash.

Can you let me know what coding was needed to get the screen to work and was it done on Bimmercode?

Thanks in advance!

what sort of damage are you seeing? The one I bought had the anti-reflective coating coming off, but I just wiped it all off and found a matte screen protector online

for coding, I followed the guide linked above!

 

[camchalmers]

Yes it is the anti-reflective coating looking patchy that put me off - was it easy to remove? Thanks for the heads u on the link, I read through it in the past but noted the coding wasn't done via Bimmercode, which I have. Thanks for your help with this, sounds like I can pick up a used screen and sort it myself.

yeah took me about 30 minutes or so with some anti-bacterial wipes

ah yeah I used BimmerCode, just followed the same steps in the expert mode!

it’s all in the head unit section.

HU_ENTRYNAV > EXBOX > DISPLAY_VARIANTE = "breites_display"

HU_ENTRYNAV > HMI > DISPLAY_SIZE_RESOLUTION = "8.8_1280x480"

Then:

CID_DISPLAY_RES: 1280_480 [02]
CID_DISPLAY_SIZE: 8_8 [03]

The second two are only needed if you have a reversing camera!

 

[camchalmers]

yeah took me about 30 minutes or so with some anti-bacterial wipes

ah yeah I used BimmerCode, just followed the same steps in the expert mode!

it’s all in the body domain controller section.

HU_ENTRYNAV > EXBOX > DISPLAY_VARIANTE = "breites_display"

HU_ENTRYNAV > HMI > DISPLAY_SIZE_RESOLUTION = "8.8_1280x480"

Then:

CID_DISPLAY_RES: 1280_480 [02]
CID_DISPLAY_SIZE: 8_8 [03]

The second two are only needed if you have a reversing camera!

I also did cornering front fog lights if that’s something you fancy!


Section 3062:
MAPPING_ABBIEGEL_L_OUTPUT: off→3 (custom value)
MAPPING_ABBIEGEL_R_OUTPUT: off→4 (custom value)

Section 3066:
KL_ENABLE_LI :KL_Aus→KL_Ein

Section 3073:
KL_ENABLE_RE : KL_Aus→KL_Ein
C_BLC_ENA :F015_disable→F015_enable
C_CLC_ENA :F015_disable→F015_enable

All within BDC (body domain controller)